FRIENDS MOBILE CARE
Welcome To Friends Mobile Care
information some file & folder are hidden see full file & folder so plz REGISTER & LOGIN

How to modify faulty FBUS RAP3V4 Cables (X3) which doesn't boot phone**

Go down

a How to modify faulty FBUS RAP3V4 Cables (X3) which doesn't boot phone**

Post by preet123 on Tue 20 Apr 2010, 7:07 pm

Hi,
these days, new Nokia phones based on RAP3v4 gave us new oppurtinies. New loaders, new protocols... Also new oppurtinity to cable makers. These new RAP3 processors running on very high frequencies, and are very sensitive to every glitch / noise on clock line, so is easy to loose flashbus synchronization with mobile. Before using RAP3v4 flashing, make sure you have GOOD QUALITY FBUS cable, I think no China cable currently on market are tested with flashing this new mobiles. Before start flashing your phone, disassemble your cable and...

1. Check if MBUS line is repli_cated well (first batch of cables delivered by GPG don't had MBUS repli_catedt and phone can't boot). Marked blue on picture. If those two points aren't connected, just cross them.
2. Check if digital ground is conneted with "normal" ground. Not many China cable makers doing it, i think 4mm of copper wire cost too much... Marked red on picture.
3. Apart from this, check of short-circuits of MBUS line. Even MBUS is shorted with unused but connected pin, it may introduce glitches/noises and synchronization with mobile may be lost ANYTIME.
4. At last, if some problem with flashing occurs - SHORT your cable as much as possible (marked yellow)- let say 2-3cm, recross it to avoid TX2 adapter. Other solution may be using better quality of copper wires and start manufacutring SHIELDED cables. Maybe some day GPG or someone else will introduce such high-quality cables?

https://redcdn.net/ihimizer/i/x3mod.jpg/

Scanning avaiable products...
Processing C:\Program Files\Nokia\Phoenix\Products\...
Processing C:\Program Files\Common Files\Nokia\DataPackage\Products\...
Found 128 products, Filtering BB5 Products - wait...
44 Products left after filtering. Ready.
Retrieving Variants for Product RM-540 - wait...
1 Variants Retrieved
Processing pre flash tasks...
Backing up RPL...
RPL Creation started...
Processing CMT Part...
Storing Product Code...
Storing PSN...
Storing HWID...
Trying to store Simlock...
Reading Configuration Key...
Hashing...
Reading SHA1-RSA Signature...
Reading SHA1-HMAC Signature...
Storing Simlock...
Trying to store WMDRM RPL...
Reading Keys...
Storing WMDRM PD...
Reading Security Block...
Security block OK and saved to "RM-540_357977037713128_2010-04-06_224942.SecurityBlock.PM"
WARNING: "22400005F42C0E49613E9CD0474C78E67661FA0C.C00039CA " Not Exists, Will read it...
Reading CYC file from phone...
Booting RAP...
CMT_SYSTEM_ASIC_ID: 000000010000022600000001020C192102034100
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 22400005F42C0E49613E9CD0474C78E67661FA0C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 7B045400E1752022F9EB80B0DEA9C65D
CMT_BOOT_ROM_CRC: 67E82268
CMT_SECURE_ROM_CRC: F29CEA60
Prepare phone failed with message -> Not found required CMT Secondary Loader
Neither CYC file and exists or failed to read it from phone (Failed to Boot / Prepare Phone)
Booting RAP...
CMT_SYSTEM_ASIC_ID: 000000010000022600000001020C192102034100
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 22400005F42C0E49613E9CD0474C78E67661FA0C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 7B045400E1752022F9EB80B0DEA9C65D
CMT_BOOT_ROM_CRC: 67E82268
CMT_SECURE_ROM_CRC: F29CEA60
RAP3Gv40_2nd.fg, Type: 2nd Boot Loader, Rev: 513.9.50.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND
RAP3Gv40_XSR17_alg.fg, Type: Algorithm, Rev: 513.9.50.0, Algo: XSR 1.6
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: CEFA9C410038BD7D17C4C6F107F1EC02C98CA69E
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Storing NPC...
Storing CCC...
Storing HWC...
CMT VARIANT Not Found
Restarting MCU...
RPL Saved OK
RPL backup thread finished, continuing...
Pre flash tasks finished, continuing...
Processing rm540__04.11.mcusw (CMT)...
Booting RAP...
CMT_SYSTEM_ASIC_ID: 000000010000022600000001020C192102034100
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 22400005F42C0E49613E9CD0474C78E67661FA0C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 7B045400E1752022F9EB80B0DEA9C65D
CMT_BOOT_ROM_CRC: 67E82268
CMT_SECURE_ROM_CRC: F29CEA60
rm540__04.11.mcusw, Type: Flash Image, Algo: BB5, XSR 1.6
RAP3Gv40_2nd.fg, Type: 2nd Boot Loader, Rev: 513.9.50.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND
RAP3Gv40_XSR17_alg.fg, Type: Algorithm, Rev: 513.9.50.0, Algo: XSR 1.6
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: CEFA9C410038BD7D17C4C6F107F1EC02C98CA69E
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00020000-0x000203FF, ONENAND
EraseArea[0,CMT]: 0x00060000-0x0009FFFF, ONENAND
EraseArea[0,CMT]: 0x000A0000-0x0025FFFF, ONENAND
EraseArea[0,CMT]: 0x003E0000-0x005DFFFF, ONENAND
EraseArea[0,CMT]: 0x005E0000-0x010DFFFF, ONENAND
EraseArea[0,CMT]: 0x01EC0000-0x01EDFFFF, ONENAND
EraseArea[0,CMT]: 0x027C0000-0x02CBFFFF, ONENAND
EraseArea[0,CMT]: 0x077C0000-0x07B3FFFF, ONENAND
EraseArea[0,CMT]: 0x010E0000-0x01EBFFFF, ONENAND
Erase Partition (CMT)
Erase Partition (CMT)
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 0.407s
Writing all blocks...
Writing CMT ADA Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT PASUBTOC Certificate...
Writing CMT PAPUBKEYS Certificate...
Writing CMT RAP3NAND Certificate...
Writing CMT UPDAPP Certificate...
Writing CMT DSP0 Certificate...
Writing CMT MCUSW Certificate...
Writing CMT MCUSW1 Certificate...
Writing CMT GENIO_INIT Certificate...
Writing CMT ISA+DYNSW Certificate...
Programming Status OK!
All blocks written OK! Time taken 33.265s
Flashing Speed: 6536,82 kBit/S
Restarting MCU...
Processing rm540__04.11.mcusw (APE)...
Processing rm540__04.11.ppm_b (CMT)...
Booting RAP...
CMT_SYSTEM_ASIC_ID: 000000010000022600000001020C192102034100
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 22400005F42C0E49613E9CD0474C78E67661FA0C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 7B045400E1752022F9EB80B0DEA9C65D
CMT_BOOT_ROM_CRC: 67E82268
CMT_SECURE_ROM_CRC: F29CEA60
rm540__04.11.ppm_b, Type: Flash Image, Algo: BB5, XSR 1.6
RAP3Gv40_2nd.fg, Type: 2nd Boot Loader, Rev: 513.9.50.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND
RAP3Gv40_XSR17_alg.fg, Type: Algorithm, Rev: 513.9.50.0, Algo: XSR 1.6
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: CEFA9C410038BD7D17C4C6F107F1EC02C98CA69E
Flashbus Write baud set to 5.0Mbits
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x01EE0000-0x027BFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.62s
Writing all blocks...
Programming Status OK!
All blocks written OK! Time taken 8.156s
Flashing Speed: 6651,99 kBit/S
Restarting MCU...
Processing rm540__04.11.ppm_b (APE)...
Processing rm540__04.11.image_b_0580752_001 (CMT)...
Booting RAP...
CMT_SYSTEM_ASIC_ID: 000000010000022600000001020C192102034100
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 22400005F42C0E49613E9CD0474C78E67661FA0C
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 7B045400E1752022F9EB80B0DEA9C65D
CMT_BOOT_ROM_CRC: 67E82268
CMT_SECURE_ROM_CRC: F29CEA60
rm540__04.11.image_b_0580752_001, Type: Flash Image, Algo: BB5, XSR 1.6
RAP3Gv40_2nd.fg, Type: 2nd Boot Loader, Rev: 513.9.50.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000321, Samsung, ONENAND
RAP3Gv40_XSR17_alg.fg, Type: Algorithm, Rev: 513.9.50.0, Algo: XSR 1.6
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: CEFA9C410038BD7D17C4C6F107F1EC02C98CA69E
Flashbus Write baud set to 5.0Mbits
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x02CC0000-0x077BFFFF, ONENAND
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 1.125s
Writing all blocks...
Programming Status OK!
All blocks written OK! Time taken 17.47s
Flashing Speed: 6571,19 kBit/S
Restarting MCU...
Processing rm540__04.11.image_b_0580752_001 (APE)...
All images processed OK! Processing post flash tasks...
Reading info...
MCU Version V 04.11
MCU Date 09-12-09
Product RM-540
Manufacturer (c) Nokia
IMEI 357977037713128
Mastercode 4546402767
IMEI Spare 3A75790773171302
IMEI SV 3375790773171312F1000000
PPM V 04.11, 09-12-09, RM-540, (c) Nokia , B
CNT Content: b_0580752, V 04.11, 09-12-09, RM-540, (c) Nokia ,
PSN KRD472552
Product Code 0580753
Module Code 0204201
Basic Product Code 0578316
PSD 0000000000000000
LPSN 0
RETU 40
TAHVO 00
AHNE 41
HW 2000
RFIC 0800
DSP ICPR91_09w44_RC
LCD SEIKO
Simlock Server SIMLOCK SERVER
Simlock Key 2440700000000000
Simlock Profile 0000000000000000
Simlock Key Cnt 0
Simlock FBUS Cnt 0
Simlock [1,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [1,2] State: OPENED Type: GID Data: FFFF
Simlock [1,3] State: OPENED Type: GID Data: FFFF
Simlock [1,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [1,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [2,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [2,2] State: OPENED Type: GID Data: FFFF
Simlock [2,3] State: OPENED Type: GID Data: FFFF
Simlock [2,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [2,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [3,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [3,2] State: OPENED Type: GID Data: FFFF
Simlock [3,3] State: OPENED Type: GID Data: FFFF
Simlock [3,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [3,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [4,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [4,2] State: OPENED Type: GID Data: FFFF
Simlock [4,3] State: OPENED Type: GID Data: FFFF
Simlock [4,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [4,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [5,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [5,2] State: OPENED Type: GID Data: FFFF
Simlock [5,3] State: OPENED Type: GID Data: FFFF
Simlock [5,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [5,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [6,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [6,2] State: OPENED Type: GID Data: FFFF
Simlock [6,3] State: OPENED Type: GID Data: FFFF
Simlock [6,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [6,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [7,1] State: OPENED Type: MCC-MNC Data: FFFFFF
Simlock [7,2] State: OPENED Type: GID Data: FFFF
Simlock [7,3] State: OPENED Type: GID Data: FFFF
Simlock [7,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF
Simlock [7,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF


Last edited by preet123 on Tue 20 Apr 2010, 7:08 pm; edited 1 time in total (Reason for editing : fbus not work)
preet123
preet123
CO ADMIN
CO ADMIN

Posts : 281
Point : 868
Join date : 2010-04-12
Age : 33

View user profile

Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum